Product Code: 29635

Feb Febflor Ultralay Self Levelling Resurfacing Compound 50 Bag Pallet

�

�

�

�

Feb Febfloor Heavy Duty Universal Self Levelling and Resurfacing Compound

Product Option: FBFLORULTRA-50 50 Bag Pallet

Pallet Deal:

FEBFLOR ULTRALAY is a ultra high strength, rapid setting, abrasion resistant cement based powder, which when mixed with water, can be used to level out uneven floors and screeds.

FEBFLOR ULTRALAY may be overlaid with common floor coverings or may be left as a final wearing surface.

FEBFLOR ULTRALAY will even accept vehicular traffic. and may be applied in one coat from 2-10mm in depth.

Typical surfaces include concrete and screeds, existing unglazed ceramic tiles, brick, stone etc.

When mixed as directed, the compound provides a free flowing mix that may be walked on in 2 hours and can be overlaid with ceramic tiles after only 3 hours at normal temperatures.�

Important Note:

when overlaying with other floor coverings allow 24 hours drying time for each 10mm depth.

�

Typical Uses:

For levelling and smoothing concrete and screed floors where a heavy duty floor topping is required.

�

Features and Benefits:

Fast setting, foot trafficable within 2 hours, can be tiled within 3 hours

Interior and exterior use

Can withstand vehicular traffic

Final wearing coat,

Over-paintable

Water and frost resistant

Application depth 2-10mm

�

Instructions for Use:

�

Preparation of Substrate:

Floors to be treated must be free from grease, dust and loose particles. Existing concrete screeds must be a minimum of 4 weeks old before applying this product. Always prepare floors by dampening with water then priming with PVA diluted 1 part PVA to 3 parts water to give a sound, slightly damp surface.

Internally surfaces should be primed using Everbuild PVA Bond.

Externally surfaces must be primed using Everbuild SBR Bond.

Always See Datasheet regarding priming.

�

�

Product Application:

Floors to be treated must be free from grease, dust and loose particles. Substrates must be porous. Always prepare floors by dampening with water then priming with PVA diluted 1 part PVA to 3 parts water to give a sound, slightly damp surface.

20kg of FEBFLOR ULTRALAY will require 4 litres of water. DO NOT USE EXCESS WATER. Always add the powder to water. This should be carried out by stepwise addition whilst stirring until a free flowing creamy compound is produced. Pour the mixture out into the prepared floor and allow it to find its own level. Trowel down lightly to achieve an overall thickness not exceeding 10mm. For depths above 10mm (up to 25mm) Add 1 part of clean, dry sharp sand to 1 part Febflor Ultralay. The sand should be added after mixing powder with water. It is advisable to reduce the amount of mixing water before adding sand, then top up with water to achieve the correct consistency. Note: the flow characteristics will be affected by addition of the sand. . Allow 3 days cure prior to subjecting to vehicular traffic @20�C, longer at lower temperatures.

�

Coverage:

20kg of FEBFLOR ULTRALAY mixed with 4 litres of water will cover approximately 4m2 at a depth of 3mm depending on substrate .

�

Technical Data/Typical Properties:

Appearance ������������������������������������� Grey granular powder

Pot life ������������������������������������������������ 20 minutes at 20�C

Cleaning ��������������������������������������������� All tools and equipment should be cleaned with water

Application Temp���������������������������� 4oC to 35oC

Overlay time������������������������������������� 3-8 hours @20oC depending on covering used

Thickness������������������������������������������� 2mm- 10mm

�

"Important Note this is a non returnable product "

while in our care all products are kept in a climate controlled store room.

because this is a reactive product we could not resell the product.

The Product should be stored out of direct sunlight until used.

�