Product Code: 29941
Mira?4400 is a ready to use highly flexible synthetic latex coating developed for application to a broad range of construction substrates prior to tiling. The cured coating remains elastic and forms a seamless barrier to water. Main application areas are internal and external walls and floors where water protection is required including wetrooms, bathrooms, showers, terraces and balconies.\n\nHighly elastic, viscous material for water insulation in wet rooms: bathrooms, terraces, balconies, washing room’s etc.\nCharacteristics\n\nWaterproof \nFrost resistant (after hardening)\nNo thinners \nHighly adhesive\nFor indoor and outdoor use\nApplicable on vertical and horizontal surfaces \nFor use directly under tile substrate \nForms rubber-like membrane after drying-up \nEasy in preparation Use\n\nUsed for forming of 100% waterproof, elastic, joint-less membrane for water insulation on floors, walls, in wall and wall/floor corners, connections of wall joints between panels or elements, pipe junctions in wet zone of wet rooms. 4400 multicoat is used as a humidity and water protection layer on concrete floor, plaster, light weight concrete, fully joint brick wall, cement or anhydrite based substratescreed, plaster board, wooden based panels and old ceramic facings.\nThe water shall be “pressure-free” i.e. 4400 multicoat must not be used in swimming pools etc. Is also applicable on heated substrates. Ceramic, clinker and stone tiles can be fixed directly on the multicoat layer.\nSubstrate preparationThe substrate must be dry, compact, cleaned of dust, grease, oil etc. Concrete slurry (if any) should be removed, weaker parts of substrate should be removed and then repaired again. Remove dust with a vacuum cleaner. Grease, oil, dirt should be cleaned with 7110 base cleaner. The entire surface should be clean of dust.\nAbsorptive substrates should be primed with mira 4180 sealer, thinned with water in the ratio: 1 part of 4180 sealer and 3 parts of water. Non-absorptive substrates e.g. painted or made of ceramic tiles shall not be primed. When the surface is dry mira 4400 multicoat can be applied.\nTechnical conditions\n\nMixing - 4400 multicoat is ready-to-use and must not be thinned. Stir slowly the mass in the can/bucket before use.\nApplication -Spread the mass with a brush, roll or a trowel. First protect corners, wall/wall and wall/floor, joints between panels or elements by covering them with two layers of 4400 multicoat filled with safe coat strip; water installation inlets and wateroutlets should be protected with special flanges of safe coat called seal manchet. On walls 2 layers of 4400 multicoat should be laid, without safe coat. The second layer should be spread when the first is dried-up after 1-2 hours.\nOn floors 2 layers of 4400 multicoat should be applied, with safe coat as a carrying layer.\nFloor insulation should be done during one working cycle. The safe coat mat should be covered completely with the second layer of 4400 multicoat to reach the proper thickness of min. 1,5 mm.\nTemperature/weather condition - Minimum air and substrate temperature +6?C When applied outdoor (terraces, balconies), protect the mass from intensive sunlight and rain.\nApplication time - Non used 4400 multicoat in the packing can be stored in closed can/bucket.\nHardening time - The membrane is totally dry after approx. 12 hrs in the temperature of 10-15?C.\n\n?\nConsumption:Walls: min. 1 kg/m2Floor: min. 1,5 kg/m2Connections wall / floor, wall corners, joints of panels and elements: 200 – 300g/running meter\nTechnical dataBased on synthetic latex, binders and mineral pigmentsExtensibility ca. 1200%Temperature resistance -20 to + 120?CMembrane thickness wall min. 1 mm – floor min. 1,5 mmStepping-on / tile laying after 12 hrs\n?\n?\n\n\n?
Visit the Pure Adhesion Ltd website for more information on Mira 4400 Multicoat Waterproof Tanking Solution - 6kg