Product Code: 31171
A spirit based, silicone impregnator that penetrates into the surface of stone and forms an invisible film within the pores and capillaries. Prevents staining from water, dirt and oil, allowing the stone to breathe, and aids maintenance. For use on all polished and unpolished natural and artificial stone.\nDescription: A special, ready-to-use product from the Lithofin range for marble, natural and artificial stone. Lithofin MN Stain-Stop contains silicones and hardeners that repel water and oil effectively. Lithofin MN Stain-Stop penetrates into the surface and forms a thin, invisible film in the capillaries. This stops oils from penetrating the surface for about 6-24 hours for marble and granite and up to 8 days for limestone. Within this time, it is possible to wipe away oils without leaving stains. The effect depends on the absorbed quantity of the product. Using Lithofin MN Stain-Stop does not usually affect the appearance of the stone, however, some intensification of colour may occur in darker stone types. It is UVresistant (yellowing of stone will not occur) and dries without leaving a sticky residue. The active ingredients pose no health hazard after drying\nField of application and suitable surfaces: Lithofin MN Stain-Stop is used as a stain repellent for all marble, natural and artificial stone surfaces. Particularly suitable for walls and floors of kitchens, bathrooms and other areas at risk from staining, as well as for table tops, window sills and domestic surfaces. Polished and ground marble, polished and natural cleft limestone, slate, varying finishes of granite, reconstituted stone, artificial stone, terrazzo and resin bonded stone.\nPlease note: With polished marble, red wine, ketchup or cola can cause etching. Never allow Lithofin MN Stain-Stop to dry on the surface, as it is not easily removed. Only to be used on absorbent and dry surfaces. Glass, ceramics and surfaces sensitive to solvents must be protected. A test area is advised before full treatment.\nDirections for use: The stone surfaces to be treated must be clean and dry. On an absorbent surface, apply generously and evenly with a brush or lambs wool roller. On less absorbent surfaces apply with a brush or cloth. Within 30-40 minutes, treat the surface again to permit the impregnator to be absorbed. Then after 30 minutes remove any residue completely using a cloth. Over large surfaces, draw off excess material using a window rubber and polish using a using a Numatic scrubbing machine with a 3M polishing pad.\nCoverage: dependent on absorbent properties of stone: about. 15m2/L for polished stone surfaces. About 6-8m2/L, for natural and sawn stone. About 3-6m2/L, for porous sandstone and highly porous limestone.\nDrying time: preliminary drying: 2 hours (safe to walk on with smooth sole shoes). Complete drying: 24-48 hours (full effectiveness of impregnator).\nAfter Treatment: for regular washing of floors we recommend Lithofin Easy-Care Cleaner, which supports the effect of Lithofin MN Stain-Stop.\nDurability: Used outdoors, Lithofin MN Stain-Stop is effective for about 5-10 years. Used indoors, durability depends on aftercare products but expect Lithopfin MN Stain-Stop to remain effective for up to 10 years with the correct ongoing maintenance.\nSafety: Keep out of reach of children. Ensure good ventilation during and after application. Do not use large quantities in rooms in which open or lightly wrapped foodstuffs are stored. Avoid naked flames. Labelling requirements in accordance with Dangerous Material Regulations or EC Guide Line 88/379: Inflammable. RID/ADR: Class 3, No. 31c (does not apply to cartons with 0,5 L, 1 L or 5 L).\nContents: According EC recommendation: siloxane, iso paraffins, white spirit.\nStorage: In a dry, cool place. Closed containers have a shelf life of at least 12 months.\nTechnical data: Density: 0,78g/cm3Flash point: 22?CAppearance: colourlessOdour: white spirit, ethylacetateReduction of water absorption: 90-95%Water vapour permeability: 80-90%\nPackaging: 0.5 litre bottle with childproof cap (10 per carton); 1 litre bottle with childproof cap (10 per carton); 5 litre container (2 per carton).\nEnvironmental protection: Contains organic solvents, free of chlorinated hydrocarbons.\nDisposal: Hand over to special waste collectors. Empty containers, which are clean or have dried out may be recycled through collection system.\nThis information is provided without guarantee. The product should be used taking into account the local conditions and the surface to be treated. In all cases of doubt, test the product first in an inconspicuous area.\nPlease Note: We are unable to ship this item outside of mainland Great Britain (Northern Ireland, Channel Islands, Republic of Ireland etc.) in accordance with regulations on the tranpsort of dangerous goods.
Visit the Pure Adhesion Ltd website for more information on Lithofin MN Stain Stop Natural Stone Impregnator & Sealer - 500ml