Product Code: 30557
Wet room shower trays specifically designed for the UK market. AquaFix wet room shower trays are manufactured in the UK to exacting an specification which is well in excess of British Standards relating to wet room installations.\nProduct Attributes:\n\nManufactured with a pre-formed slope, to allow water to flow efficiently to the drain.\nFully waterproof, closed cell, high density extruded polystyrene shower former.\nFor use with Aquafix 600m Linear Waste system (steel or tileable) only.\nEasy to install in conjunction with most tile backer boards and?tanking systems.?\nAvailable in a range of sizes to suit all requirements.\nSuitable for tiles 23mm square and above?(bare foot traffic only on 23mm tiles)\nManufactured to fit Aquafix high flow square shower trapped drain system (60 litres per minute)\nCreated with a 10mm fall from the edge of the tray to the waste.\nDrain upgrades available; including linear system, premium 6mm solid stainless steel and tileable option.\nTray sizes made to fit with?AquaFix glass panel shower screens.\nFull range of AquaFix designer accessories available.\nGreat Value; ideal for DIY and professional?use.\nDesigned & manufactured in the UK to suit UK plumbing fixtures and fittings.\nSuitable for use with electrical underfloor heating systems.\n\nPlease Note: The centre of the waste is 200mm from the edge of the tray.\nAquaFix trays are made from premium grade, high density extruded polystyrene which is coated in specially formulated cement render which has a re enforcing mesh embedded within it. When installed onto joists (following infill and support procedure) the trays will sit perfectly level in most UK bathrooms floors which have 20mm existing floor.?This is overboarded with 10mm tile backer boards to acheive a?consistent 30mm tray and floor.\nAquaFix also provide a solution to installation onto solid floors using the raised access kits which create a tileable step-up into the shower area which is sufficient to run pipework and locate the gully inside the raised waterproof?platform.\nMore Useful Information About Aquafix Foam:\n\nAquaFix foam products are all covered by a 10 year guarantee against manufacturing defects.\nAquafix foam products have a GWP (Global Warming Potential) of ZERO.\nAquafix foam products have a?ODP (Ozone Depletion Potential) of ZERO \n\nAquafix Linear Shower Gully Features\n\nDesigned for use with Aquafix Wet Room Shower Trays only.\nGrate Size (Tileable or Steel): 600 x 40mm\nRemovable hair trap\nHigh flow trap (60L per minute)\nHorizontal Outlet pipe size 2", with 1 1/2" reducer (UK Solvent weld fitting)\nMulti directional outlet with blanking plate\nDimensions of trap under installed tray: 170x80x80mm (length x width x depth)\n\nIMPORTANT INSTALLATION INFORMATION FOR TILEABLE GULLY:Tile inserts for the linear drain should be stuck down using silicone sealant and the insert can a be a maximum of 12mm including the silicone. Thicker tile inserts can be used but the insert will simply sit higher than the stainless steel frame the tile sits in.When using the tileable drain, the depth of the tile on the tray plus the adhesive underneath must be 13mm or more. This ensures tray tiles can finish level with the tileable drain insert. We recommend testing the insert and tray tiles to check they work together before starting to tile the tray.\n \n \n \nIMPORTANT INSTALLATION INFORMATION FOR STEEL TOP GULLY:Maximum Tile Thickness For Linear Drain = 14mm including adhesive.NB: If the installation kit has been purchased, squares of sealband tape can be cut and stuck onto the height adjustable supports for the drain cover to raise it. This would allow for thicker tiles to be used on the tray without the stainless steel drain cover being lower than the level of the tiles.
Visit the Pure Adhesion Ltd website for more information on AquaFix Wetroom Shower Tray - 1200x1200x30mm - 600mm Linear End Waste